5 Gallon Preform Mould (18.9L)

May 27, 2023

Model NO.: HX--1003
Certification: CE
Customized: Customized
Runner: Hot Runner
Trademark: HENGXIN
Origin: Zhejiang
 

Specifications

hot runner 5 gallon preform mold with material of p20 and 2316,we offer the goods with 1 million time produce and one year guarante.

 


 

Brief Introduction

     

  • Keep 500°C about 36 hours in vacuum station to eliminate the stress, make sure the molding board steady after long time use.
  • Slipper block use HUSKY type, with material of steel P20, which is highly anticorrosion, all the move parts used advanced ion nitration treatment, the surface hardness is HRC48-52.

Spare Parts(screw, coin and cavity)

All uses material steel 2316, with high anticorrosion and hardness is HRC46-48.

 

Hot Runner: use SKH61 temperature resistance material, with hardness HRC≥46

 

  1. The hot nozzle use Italy ROTFIL or german HOTSET heating coil to make sure the quality.
  2. Plastic injection opening use high hardness QBE2 beryllium copper, with good conduct heat, anti wear and steady.
  3. Plastic injection opening heat insulation cap use American Dupont.
  4. Piston and cylinder use import wear ring, the piston use material 2136, the sealing element used import sealing element, with material of poly four vinyl chloride.
     

         

     

    HOT RUNNER SYSTEM  

     

    The hot runner adopts the PID controlling system. It has the function of the self repair and self protection. Which can prolong life of the heating element. The temperature difference under controlling within 1°C difference. It will make sure that raw material can not be burnt insider of the hot runner. The wastage will be kept less than 1% the new sprayer design make the mould are easy for maintaining, the ejected part of the sprayer, the heating part, the heat insulation part,

     thermocouple part can be changed without disassembling the mould which can save a lot of the time and save the maintaining cost.

     

     

        PET PREFORM MOULD PARTS


         

    1. Cores: stainless steel with titanium-nitrate core surface finish
    2. Locking rings: with air-assisted preform ejection.
    3. Neck rings: stainless steel, water cooled
    4. Cavities: highly polished and chromed surfaces
    5. Gate inserts: stainless steel with highly polished surfaces

     

     

    THE EMBRYO SHOW 


    5 Gallon Preform Mould (18.9L)

     

         

     

     

     

     

     

     

    HOT RUNNER controlling system for PET preform mould


         

     
    5 Gallon Preform Mould (18.9L)

     

     

     The PET preform and the end products show

     

    5 Gallon Preform Mould (18.9L)

     

     

     

     

     
     

    Dog Food Production Line

    1. Raw material pulverization: Raw materials are mainly divided into two categories, starch and fat. Starch is mainly various grains. Its pulverization can be achieved by ordinary pulverizers. It only needs to ensure the fineness and clean raw materials during the pulverization process. Hygiene can be. Use a colloid mill to pulverize into separate packs or puree, and the meat only needs to be pulverized into meat puree or powder with a colloid mill, and then added to the grain powder and stirred evenly.
    2. Raw material mixing: The mixing equipment has two functions, one is to mix all kinds of raw materials evenly, and the other is to adjust the moisture and humidity. It is generally a vertical rapid mixer: the mixing time is short, the mixing is completed quickly, and the machine is used before the humidity of the raw material changes significantly, which ensures the uniformity and quality of the puffing of the dog food particles. The disadvantage is: the single-cylinder mixing capacity is small, and it needs to be stirred all the time during the production process.
    3. Raw material extrusion, puffing and curing molding: The twin-screw extruder extrudes and extrudes under high temperature and high pressure, and produces dog food and cat food particles of different styles and shapes by changing different molds. For different raw material ratios and humidity, it is necessary to adjust the temperature and screw speed of different regions and the feeding speed of the feeder to ensure that the produced dog food particles are of high quality and good appearance.

    Pet food production line,Dog food production line,Cat food production line

    Jump Machinery (Shanghai) Limited , https://www.fruitsmachinery.com